Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
Type 321 Stainless Steel
Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved. VERSION 1 (2/18/2014): PAGE 1 of 11 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Technical Data Sheet ATI 321™/ATI 347™/ATI 348™ ATI 321™/ATI 347™/ATI 348™ Stainless Steel: Austenitic (UNS S32100, S34700, S34800) GENERAL INFORMATION ATI 321™ (UNS S32100), ATI 347™ (UNS S34700), and ATI 348™ (UNS S34800) alloys are stabilized stainless steels which offer as their main advantage an excellent resistance to intergranular corrosion following exposure to temperatures in the chromium carbide precipitation range from 800 to 1500°F (427 to 816°C). ATI 321 alloy is stabilized against chromium carbide formation by the addition of titanium. ATI 347 and ATI 348 alloys are stabilized by the addition of columbium and tantalum. ATI 348 alloy has restricted cobalt and tantalum content for nuclear applications. W hile ATI 321, ATI 347 and ATI 348 alloy continue to be employed for prolonged service in the 800 to 1500°F (427 to 816°C) temperature range, ATI 304L™ alloy has supplanted these stabilized grades for applications involving only welding or short time heating. (For information on ATI 304L alloy, consult the Technical Data Sheet for ATI 304L™ alloy.) ATI 321, ATI 347 and ATI 348 stainless steels are also advantageous for high temperature service because of their good mechanical properties. ATI 321, ATI 347 and ATI 348 stainless steels offer higher creep and stress rupture properties than ATI 304 alloy and, particularly, ATI 304L stainless which might also be considered for exposures where sensitization and intergranular corrosion are concerns. This results in higher elevated temperature allowable stresses for these stabilized alloys for ASME Boiler and Pressure Vessel Code applications. The ATI 321, ATI 347 and ATI 348 alloys have maximum use temperatures of 1500°F (816°C) for code applications as does ATI 304™ stainless, whereas ATI T304L™ stainless is limited to 800°F (426°C). The properties of ATI 348 stainless are similar to the properties of ATI 347 alloy, and according to ASTM A240 their chemical compositions are the same except for tantalum and cobalt contents. High carbon versions of all three alloys are available. These grades have UNS designations S32109, S34709, and S34809. PRODUCT FORMS ATI 321, ATI 347 and ATI 348 stainless steel is available in plate, sheet, and strip forms from ATI. CORROSION R ESIST ANCE General Corrosion ATI 321, ATI 347 and ATI 348 alloys offer similar resistance to general, overall corrosion as the unstabilized chromium-nickel ATI 304 stainless. The ATI Technical Data Sheet on ATI 304 may be consulted for an indication of resistance to corrosive media. Heating for long periods of time in the chromium carbide precipitation range may affect the general resistance of ATI 321, 347 and 348 stainless in severe corrosive media. In most environments, all three alloys will show similar corrosion resistance; however, ATI 321 alloy in the annealed condition is somewhat less resistant to general corrosion in strongly oxidizing environments than annealed ATI 347 alloy. For this reason, ATI 347 stainless is preferable for aqueous and other low temperature environments. Exposure in the 800 to 1500°F (427 to 816°C) temperature range lowers the overall corrosion resistance of ATI 321 alloy to a much greater extent than ATI 347 alloy. ATI 347 and ATI 348 stainless are used primarily in high temperature applications where high resistance to sensitization is essential, thereby preventing intergranular corrosion at lower temperatures. Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved. VERSION 1 (2/18/2014): PAGE 2 of 11 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Technical Data Sheet ATI 321™/ATI 347™/ATI 348™ Intergranular Corrosion ATI 321, ATI 347 and ATI 348 stainless steels are useful in applications where the unstabilized chromium-nickel steels, such as ATI 304 stainless steels, would be susceptible to intergranular corrosion. When the unstabilized chromium-nickel steels are held in or slowly cooled through the range of 800 to 1500°F (427 to 816°C), chromium carbide is precipitated at the grain boundaries. In the presence of certain strongly corrosive media, these grain boundaries are preferentially attacked, a general weakening of the metal results, and a complete disintegration may occur. Organic media or weakly corrosive aqueous agents, milk and other dairy products, or atmospheric conditions rarel y produce intergranular corrosion even when large amounts of precipitated carbides are present. W hen thin gage material is welded the time in the temperature range of 800 to 1500°F (427 to 816°C) is so short that with most corroding media the unstabilized types are generally satisfactory. The extent to which carbide precipitation may be harmful depends upon the length of time the alloy was exposed to 800 to 1500°F (427 to 816°C) and upon the corrosive environment. Even the longer heating times involved in welding heavy gages are not harmful to the unstabilized "L" grade alloys where the carbon content is kept to low amounts of 0.03% or less. The high resistance of the stabilized ATI 321, 347 and 348 stainless steels to sensitization and intergranular corrosion is illustrated by data for the ATI 321 alloy in the Copper-Copper Sulfate –16% Sulfuric Acid Test (ASTM A262, Practice E) below. Mill annealed samples were given a sensitizing heat treatment consisting of soaking at 1050°F (566°C) for 48 hours prior to the test. Intergranular Corrosion Test Long-Term Sensitization* Results ASTM A262 Practice Alloy Rate (ipm) Bend Rate (mpy) ATI 304™ 0.81 dissolved 9720.0 ATI 304L™ 0.0013 IGA 15.6 ATI 321™ 0.0008 IGA 9.6 ATI 347™ 0.0005 NO IGA 6.0 *Annealed 1100°F, 240 hours The absence of intergranular attack (IGA) in the ATI 347 specimens shows that they did not sensitize during this thermal exposure. The low corrosion rate exhibited by the ATI 321 specimens shows that even though it suffered some IGA, it was more resistant than ATI 304L under these conditions. All of these alloys are far superior to regular ATI 304 stainless steel under the conditions of this test. In general, ATI 321, ATI 347 and ATI 348 alloys are used for heavy welded equipment which cannot be annealed and for equipment which is operated between 800 to 1500°F (427 to 816°C) or slowly cooled through this range. Experience gained in a wide range of service conditions has provided sufficient data to generally predict the possibility of intergranular attack in most applications. Additional information can also be found in the HEAT TREATMENT section. WELD ABILIT Y Austenitic stainless steels are considered to be the most weldable of the high-alloy steels and can be welded by all fusion and resistance welding processes. Two important considerations in producing weld joints in the austenitic stainless steels are preservation of corrosion resistance and avoidance of cracking. It is important to maintain the level of stabilizing element present in ATI 321, ATI 347 and ATI 348 alloys during welding. ATI 321 alloy is more prone to loss of titanium. ATI 347 and ATI 348 alloys are more resistant to loss of columbium. Care needs to be exercised to avoid pickup of carbon from oils and other sources and nitrogen from air. Weld practices which include attention to cleanliness and good inert gas shielding are recommended for these stabilized grades as well as other non-stabilized austenitic alloys. W eld metal with a fully austenitic structure is more susceptible to cracking during the welding operation. For this reason, ATI 321, ATI 347 and ATI 348 alloys are designed to resolidify with a small amount of ferrite to minimize cracking susceptibility. Columbium stabilized stainless steels are more prone to hot cracking than titanium stabilized stainless steels. Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved. VERSION 1 (2/18/2014): PAGE 3 of 11 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Technical Data Sheet ATI 321™/ATI 347™/ATI 348™ Matching filler metals are available for welding ATI 321 and ATI 347 stabilized stainless steels. The ATI 347 filler metal is sometimes used to weld the ATI 321 alloy as well as the ATI 348 alloy. These stabilized alloys may be joined to other stainless steels or carbon steel. Type 309 (23% Cr-13.5% Ni) or nickel-base filler metals have been used for this purpose. COM POSIT ION The composition of these alloys are specified by ASTM A240 and ASME SA-240 specifications. Weight Percent Maximum Unless Range is Specified Element ATI 321™ ATI 347™ ATI 348™ Carbon* 0.08 0.08 0.08 Manganese 2.00 2.00 2.00 Phosphorus 0.045 0.045 0.045 Sulfur 0.030 0.030 0.030 Silicon 0.75 0.75 0.75 Chromium 17.00-19.00 17.00-19.00 17.00-19.00 Nickel 9.00-12.00 9.00-12.00 9.00-12.00 Columbium+Tantalum** -- 10×C min to 1.00 max 10×C min to 1.00 max Tantalum -- -- 0.10 Titanium** 5×(C+N) min to 0.70 max -- -- Cobalt -- -- 0.20 Nitrogen 0.10 -- -- Iron Balance Balance Balance *Also H grade with Carbon 0.04 - 0.10% ** H grade minimum stabilizer is different formula PHYSIC AL PRO PERTIES The physical properties of ATI 321, ATI 347 and ATI 348 stainless steels are quite similar and, for all practical purposes, may be considered to be the same. The values given in the table below may be used to apply to all three steels. When properly annealed, the ATI 321, ATI 347 and ATI 348 stainless steels consist principally of austenite and carbides of titanium or columbium. Small amounts of ferrite may or may not be present in the microstructure. Small amounts of sigma phase may form during long time exposure in the 1000 to 1500°F (593 to 816°C) temperature range. The stabilized ATI 321, ATI 347 and ATI 348 stainless steels are not hardenable by heat treatment. The overall heat transfer coefficient of metals is determined by factors in addition to thermal conductivity of the metal. In most cases, film coefficients, scaling, and surface conditions are such that not more than 10 to 15 percent more surface area is required for stainless steels than for other metals having higher thermal conductivity. The ability of stainless steels to maintain clean surfaces often allow better heat transfer than other metals having higher thermal conductivity. Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved. VERSION 1 (2/18/2014): PAGE 4 of 11 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Technical Data Sheet ATI 321™/ATI 347™/ATI 348™ Magnetic Permeability The stabilized ATI 321, ATI 347 and ATI 348 alloys are generally non-magnetic in the annealed condition with magnetic permeability values typically less than 1.02 at 200H. Permeability values may vary with composition and will increase with cold work. Permeability of welds containing ferrite will be higher. Density Grade g/cm3 lb/in3 ATI 321™ 7.92 0.286 ATI 347™ 7.96 0.288 ATI 348™ 7.96 0.289 Modulus of Elasticity in Tension 28 x 106 psi (193 GPa) Mean Coefficient of Linear Thermal Expansion Temperature Range cm/cm °C in/in °F °C °F 20 - 100 68 - 212 16.6 x 10-6 9.2 x 10-6 20 - 600 68 - 1112 18.9 x 10-6 10.5 x 10-6 20 -1000 68 - 1832 20.5 x 10-6 11.4 x 10-6 Thermal Conductivity Temperature Range W/m·K Btu·in/hr·ft2·°F °C °F 20 - 100 68 - 212 16.3 112.5 20 - 500 68 - 932 21.4 147.7 Specific Heat Temperature Range J/kg K Btu/lb °F °C °F 0 - 100 32 - 212 500 0.12 Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved. VERSION 1 (2/18/2014): PAGE 5 of 11 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Technical Data Sheet ATI 321™/ATI 347™/ATI 348™ Electrical Resistivity Temperature Range microhm·cm °C °F 20 68 72 100 213 78 200 392 86 400 752 100 600 1112 111 800 1472 121 900 1652 126 Melting Range °C °F 1398-1446 2550-2635 M ECHANIC AL PRO PERTIES Room Temperature Tensile Properties Minimum mechanical properties of the stabilized ATI 321, ATI 347 and ATI 348 chromium-nickel alloys in the annealed condition 2000°F (1093°C, air cooled) are shown in the table below. The test samples were prepared from sheet material. Elevated Temperature Tensile Properties Typical elevated temperature mechanical properties for ATI 321, ATI 347 and ATI 348 sheet/strip are shown below. The strength of these stabilized alloys are distinctly higher than that of non-stabilized ATI 304 alloy at temperatures of 1000°F (538°C) and above. High carbon ATI 321H™, ATI 347H™ and ATI 348H™ (UNS S32109, S34709 and S34809, respectively) alloys have higher strength at temperatures above 1000°F (537°C). ASME maximum allowable design stress data for ATI 347H stainless reflects the higher strength of this grade in comparison to the lower carbon ATI 347 alloy. The ATI 321H and ATI 348H alloys are not permitted for Section VIII applications and are limited to 800°F (427°C) use temperatures for Section III code applications. Creep and Stress Rupture Properties Typical creep and stress rupture data for ATI 321, ATI 347 and ATI 348 stainless steels are shown in the figures below. The elevated temperature creep and stress rupture strengths of the stabilized steels are higher than those of unstabilized ATI 304 and 304L alloys. These superior properties for the ATI 321, ATI 347 and ATI 348 alloys permit design of pressure containing components for elevated temperature service to higher stress levels as recognized in the ASME Boiler and Pressure Vessel Code. Impact Strength ATI 321 and ATI 347 stainless have excellent toughness at room and sub-zero temperatures. In the following table are Charpy V-notch impact values for annealed ATI 347 stainless after holding the samples for 1 hour at the indicated testing temperatures. Data for ATI 321 stainless would be expected to be similar. Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved. VERSION 1 (2/18/2014): PAGE 6 of 11 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Technical Data Sheet ATI 321™/ATI 347™/ATI 348™ Impact Strength ATI 321™, ATI 347™, & ATI 348™ Alloys Test Temperature Charpy Impact Energy Absorbed °C °F Ft-lb Joules 75 24 90 122 -25 -32 66 89 -80 -62 57 78 Minimum Room Temperature Mechanical Properties Per ASTM A240 and ASME SA-240 Type Yield Strength 0.2% Offset psi (MPa) Ultimate Tensile Strength psi (MPa) Elongation in 2 in. (%) Hardness, Maximum Plate Sheet Strip 321 30,000 (205) 75,000 (515) 40 217 Brinell 95 Rb 95 Rb 347 30,000 (205) 75,000 (515) 40 201 Brinell 92 Rb 92 Rb 348 30,000 (205) 75,000 (515) 40 201 Brinell 92 Rb 92 Rb Typical Elevated Temperature Tensile Properties ATI 321™ Alloy (0.036 inch thick / 0.9 mm thick) Test Temperature Yield Strength 0.2% Offset psi (MPa) Ultimate Tensile Strength, psi (MPa) % Elongation in 2 in. °F °C 68 20 31,400 (215) 85,000 (590) 55.0 400 204 23,500 (160) 66,600 (455) 38.0 800 427 19,380 (130) 66,300 (455) 32.0 1000 538 19,010 (130) 64,400 (440) 32.0 1200 649 18,890 (130) 55,800 (380) 28.0 1350 732 19,000 (130) 41,500 (285) 26.0 1500 816 17,200 (115) 26,000 (180) 45.0 Typical Elevated Temperature Tensile Properties ATI 347™ and ATI 348™ Alloys (0.060 inch thick / 1.54 mm thick) Test Temperature Yield Strength 0.2% Offset, psi (MPa) Ultimate Tensile Strength, psi (MPa) % Elongation in 2 in. °F °C 68 20 36,500 (250) 93,250 (640) 45.0 400 204 36,600 (250) 73,570 (505) 36.0 800 427 29,680 (205) 69,500 (475) 30.0 1000 538 27,400 (190) 63,510 (435) 27.0 1200 649 24,475 (165) 52,300 (360) 26.0 1350 732 22,800 (155) 39,280 (270) 40.0 1500 816 18,600 (125) 26,400 (180) 50.0 Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved. VERSION 1 (2/18/2014): PAGE 7 of 11 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Technical Data Sheet ATI 321™/ATI 347™/ATI 348™ Fatigue Strength The fatigue strength of practically every metal is affected by corrosive conditions, surface finish, form, and mean stress. For this reason, no definite values can be shown which would be representative of the fatigue strength under all operating conditions. The fatigue endurance limits of ATI 321 and ATI 347 stainless are approximately 35% of their tensile strengths. CREEP STRENGTH ANNEALED ATI 321™ ALLOY CREEP STRENGTH ANNEALED ATI 347™ AND ATI 347™ ALLOYS Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved. VERSION 1 (2/18/2014): PAGE 8 of 11 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Technical Data Sheet ATI 321™/ATI 347™/ATI 348™ STRESS RUPTURE STRENGTH ANNEALED ATI 321™ ALLOY STRESS RUPTURE STRENGTH ANNEALED ATI 347™ & ATI 348™ ALLOYS Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved. VERSION 1 (2/18/2014): PAGE 9 of 11 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Technical Data Sheet ATI 321™/ATI 347™/ATI 348™ OXID AT ION RESIST ANCE ATI 321, ATI 347, and ATI 348 alloys exhibit oxidation resistance comparable to the other 18–8 austenitic stainless steels. Oxidation test data for ATI 347 alloy is presented graphically and in tabular form. Specimens prepared from standard mill–finish production material were exposed in ambient laboratory air at elevated temperatures. Periodically, specimens were removed from the high temperature environment and weighed to determine the extent of scale formation. Test results are reported as a weight change in units of milligrams per square centimeter and reflect the average from a minimum of two different test specimens. Weight Change (mg/cm2) Exposure Time 1300°F 1350°F 1400°F 1450°F 1500°F 168 hours 0.032 0.046 0.054 0.067 0.118 500 hours 0.045 0.065 0.108 0.108 0.221 1,000 hours 0.067 -- 0.166 -- 0.338 5,000 hours -- -- 0.443 -- -- ATI 321, 347, and 348 alloys differ primarily b y small alloying additions unrelated to factors affecting the oxidation resistance. Therefore, these results should be representative of all three grades. However, since the rate of oxidation can be influenced by the exposure environment and factors intrinsic to specific product forms, these results should be interpreted only as a general indication of the oxidation resistance of these grades. Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved. VERSION 1 (2/18/2014): PAGE 10 of 11 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Technical Data Sheet ATI 321™/ATI 347™/ATI 348™ ST RESS CORROSION CRACKING The ATI 321, ATI 347 and ATI 348 austenitic stainless steels are susceptible to stress corrosion cracking (SCC) in halides similar to ATI 304 stainless steel. This results because of their similarity in nickel content. Conditions which cause SCC are: (1) presence of halide ion (generall y chloride), (2) residual tensile stresses, and (3) environmental temperatures in excess of about 120°F (49°C). Stresses may result from cold deformation during forming operations, or from thermal cycles encountered during welding operations. Stress levels may be reduced by annealing or stress-relieving heat treatments following cold deformation. The stabilized ATI 321, ATI 347 and ATI 348 alloys are good choices for service in the stress relieved condition in environments which might otherwise cause intergranular corrosion for unstabilized alloys. The ATI 321, ATI 347 and ATI 348 alloys are particularly useful under conditions which cause polythionic acid stress corrosion of non-stabilized austenitic stainless steels, such as ATI 304. Exposure of non-stabilized austenitic stainless steel to temperatures in the sensitizing range will cause the precipitation of chromium carbides at grain boundaries. On cooling to room temperature in a sulfide-containing environment, the sulfide (often h ydrogen sulfide) reacts with moisture and oxygen to form polythionic acids which attack the sensitized grain boundaries. Under conditions of stress, intergranular cracks form. Polythionic acid SCC has occurred in oil refinery environments where sulfides are common. The stabilized ATI 321, ATI 347 and ATI 348 alloys offer a solution to polythionic acids SCC by resisting sensitization during elevated temperature service. For optimum resistance, these alloys should be used in the thermally stabilized condition if service- related conditions may result in sensitization. Pitting / Crevice Corrosion The resistance of the stabilized ATI 321, ATI 347 and ATI 348 alloys to pitting and crevice corrosion in the presence of chloride ion is similar to that of ATI 304 or ATI 304L stainless steels because of similar chromium content. Generally, 100 ppm chloride in aqueous environments is considered to be the limit for both the unstabilized and the stabilized alloys, particularl y if crevices are present. Higher levels of chloride ion might cause crevice corrosion and pitting. For more severe conditions of higher chloride level, lower pH and/or higher temperature, allo ys with molybdenum, such as ATI 316 or AL-6XN® alloy, should be considered. The stabilized ATI 321, ATI 347 and ATI 348 alloys pass the 100 hour, 5 percent neutral salt spra y test (ASTM B117) with no rusting or staining of samples. However, exposure of these alloys to salt mists from the ocean would be expected to cause pitting and crevice corrosion accompanied by severe discoloration. The ATI 321, ATI 347 and ATI 348 alloys are not recommended for exposure to marine environments. Halide (Chloride) Stress Corrosion Tests, ATI 321™ Alloy Test U-Bend (Highl y Stressed Samples 1350°F 42% Magnesium Chloride, Boiling Base Metal Cracked, 24-71 hours Welded Cracked, 24-71 hours 33% Lithium Chloride, Boiling Base Metal Cracked Within 18 hours Welded Cracked Within 18 hours 26% Sodium Chloride, Boiling Base Metal No Cracks 1000 hours Cracked Within 475 hours Welded Cracked Within 525-621 hours HE AT T RE AT M ENT The annealing temperature range for ATI 321 and ATI 347 alloys is 1800 to 2000°F (928 to 1093°C). W hile the primary purpose of annealing is to obtain softness and high ductility, these steels may also be stress relief annealed within the carbide precipitation range 800 to 1500°F (427 to 816°C), without any danger of subsequent intergranular corrosion. Relieving strains by annealing for only a few hours in the 800 to 1500°F (427 to 816°C) range will not cause any noticeable lowering in the general corrosion resistance, although prolonged heating within this range does tend to lower the general corrosion resistance to some extent. As emphasized, however, annealing in the 800 to 1500°F (427 to 816°C) temperature range does not result in a susceptibility to intergranular attack. Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved. VERSION 1 (2/18/2014): PAGE 11 of 11 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Technical Data Sheet ATI 321™/ATI 347™/ATI 348™ For maximum ductility, the higher annealing range of 1800 to 2000°F (928 to 1093°C) is recommended. W hen fabricating chromium-nickel stainless steel into equipment requiring the maximum protection against carbide precipitation obtainable through use of a stabilized grade, it is essential to recognize that there is a difference between the stabilizing ability of columbium and titanium. For these reasons the degree of stabilization and of resulting protection may be less pronounced when ATI 321 stainless is employed. W hen maximum corrosion resistance is called for, it may be necessary with ATI 321 stainless to employ a corrective remedy which is known as a stabilizing anneal. It consists of heating to 1550 to 1650°F (843 to 899°C) for up to 5 hours depending on thickness. This range is above that within which chromium carbides are formed and is sufficiently high to cause dissociation and solution of any that ma y have been previously developed. Furthermore, it is the temperature at which titanium combines with carbon to form harmless titanium carbides. The result is that chromium is restored to solid solution and carbon is forced into combination with titanium as harmless carbides. This additional treatment is required less often for the columbium-stabilized ATI 347 and ATI 348 alloys. When heat treatments are done in an oxidizing atmosphere the oxide should be removed after annealing in a descaling solution such as a mixture of nitric and hydrofluoric acids. These acids should be thoroughly rinsed off the surface after cleaning. These alloys cannot be hardened by heat treatment. Cleaning Despite their corrosion resistance, stainless steels need care in fabrication and during use to maintain their surface appearance even under normal conditions of service. In welding, inert gas processes are used. Scale or slag that forms from welding processes is removed with a stainless steel wire brush. Carbon steel wire brushes will leave carbon steel particles in the surface which will eventually produce surface rusting. For more severe applications, welded areas should be treated with a descaling solution such as a mixture of nitric and hydrofluoric acids to remove the heat tint, and these acids should be subsequently washed off. For material exposed to inland, light industrial or milder service, minimum maintenance is required. Only sheltered areas need occasional washing with a stream of pressurized water. In heavy industrial areas, frequent washing is advisable to remove dirt deposits which might eventually cause corrosion and impair the surface appearance of the stainless steel. Design can aid cleanability. Equipment with rounded corners, fillets and absence of crevices facilitates cleaning as do smooth ground welds and polished surfaces.