Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
Strip Tolerances and Finishes
Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. U.S. and foreign patents; other patents pending. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved.. VERSION 1 (3/20/2014): PAGE 1 of 3 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Standard Tolerances Strip Standard Tolerances Stainless Steel Strip – Forms Finishes and Tolerances ATI strip stainless steels are flat-rolled products available in coils or cut lengths. Thicknesses range from 0.0015” to 0.1874” and widths up to 48”. ATI stainless strip is available within equipment limitations with any of these edges: No. 1 – Round or square produced by machining or rolling No. 3 – Produced by slitting No. 5 – Essentially square produced by shaving or rolling after slitting Each strip product is made to your specification. With proper prints, parts and description of environmental condition, the most suitable strip supplied to your specification can best be achieved. ATI offers fully integrated production of a complete line of stainless steel strip in all standard grades and finishes. These are ideal for applications requiring corrosion resistance, strength, durability, and ease of cleaning. Our Precision Rolled Strip® products are tailor-made for specific end uses in the lighter strip thicknesses. These products are typically produced to very tight dimensional, surface and metallurgical property tolerances. CAMBER Up to and including 1-1/2” wide: 1/2” maximum in any 8-foot length. Over 1-1/2” to 23.999” wide: 1/4" maximum in any 8-foot length. Camber to be determined by placing an 8-foot straight edge against the concave edge of the strip. SIZE TOLERANCES Thickness Series 200, 300 and 400 grades are measured 3/8” in from edge on 1” or wider and on narrower than 1” at any place on the strip. Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. U.S. and foreign patents; other patents pending. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved.. VERSION 1 (3/20/2014): PAGE 2 of 3 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Standard Tolerances Strip Standard Tolerances Width Narrow width tolerances are maintained on strip product, but such tolerances vary depending upon whether an as-slit edge (No. 3) or mechanically prepared edge (Nos. 1 and 5) is ordered. Data are typical, are provided for informational purposes, and should not be construed as maximum or minimum values for specification or for final design, or for a particular use or application. The data may be revised anytime without notice. We make no representation or warranty as to its accuracy and assume no duty to update. Actual data on any particular product or material may vary from those shown herein. U.S. and foreign patents; other patents pending. TM is trademark of and ® is registered trademark of ATI Properties, Inc. or its affiliated companies. ® The starburst logo is a registered trademark of ATI Properties, Inc. © 2014 ATI. All rights reserved.. VERSION 1 (3/20/2014): PAGE 3 of 3 Allegheny Technologies Incorporated 1000 Six PPG Place Pittsburgh, PA 15222-5479 U.S.A. www.ATImetals.com Standard Tolerances Strip Standard Tolerances Standard Finishes The chromium-nickel and straight chromium grades of stainless steel strip can be surface treated to provide a wide variety of finishes. #1 – Hot Rolled, annealed and pickled #1D – Cold Rolled, annealed and pickled #2D– Cold rolled, annealed, pickled, or annealed and skin passed with dull rolls. #1B – Cold rolled on polished rolls, annealed and pickled #2B – Cold rolled on polished rolls, annealed, pickled, and skin passed on polished rolls #1BA - Cold rolled on polished rolls, annealed in a protective atmosphere retaining the as-rolled surface appearance #2BA – Same as #1BA except the annealed strip receives a final skin pass. #1CBA – Dull cold rolled and annealed in a protective atmosphere #1 Bright Hardened - Martensitic grades cold rolled on polished rolls and heat treated in a protective atmosphere, retaining the as-rolled surface appearance. #2TR – Cold rolled to a temper specified by the customer Special finished are available upon request. COATINGS Adhesive vinyl coverings are available with a range of adhesive strengths for various applications. Coils up to 2000 lbs. (depending on width and gage) are available as oscillate wound. On Application Strip gages are available in up to 48" widths.